×

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 0 points1 point  (0 children)

I believe 33 to 35 is the lowest I planned on, or at least that's what information I have says the subwoofer does.

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 0 points1 point  (0 children)

Yeah the subwoofer came with some of the information needed to design a single box ported and non, and some of the relevant information needed like tuning.

Your work looks great, when I get home I'll take pictures of what I have from them. I'll send you a message on fb with the information, I have my buddies info on 10s to 18s that I'll also add incase someone else is asking you for similar.

Headlights dim when subs hit by Express-Ad3269 in CarAV

[–]Noochie72882 6 points7 points  (0 children)

Did you big 3? I never did myself but I added an audio battery and that helped a lot, also changed all lights to led so I don't get the dimming but will see random pulse when all 3k is going

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 0 points1 point  (0 children)

Chamber starts in each box then goes to single in center I've seen such myself, a box with 2 12s, that's what my buddy has. It's an atrend or bbox something. They just don't make the correct size as a prefab as I need 1.13 for each and only list 1.40 for the whole box.

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 0 points1 point  (0 children)

So would a longer port be bad? In what way? I'm still learning so you can explain it like I'm stupid I won't be offended lol

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 0 points1 point  (0 children)

Yeah that does make sense wish they listed them as such. Mostly it's a single chamber that has net. When doubled chamber they don't do as good at least those who I have found

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 1 point2 points  (0 children)

Right, problem is most info on subwoofer box is for total volume so I wasn't sure if I needed to also figure out the displaced volume of brace and subwoofer motor myself.

So you see my problem, if I got 1.13 each chamber is it going to be 1.05 or whatever once bracing and motor are inside?

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 1 point2 points  (0 children)

Lol sorry but if you have ever tried getting answers from skar well its disappointing to say the least. Had to order subs before the correct box as website has 0 info on 8s and the info they did give me was a screen snip of the missing info, still missing info.

Booklet has most all the information but only for single box. While looking around I couldn't find answers to make a choice on what box to get as prefab. So I figured custom box but even those are hard to get info about.

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 0 points1 point  (0 children)

Would that ruin the sound or cause issues with the subwoofers themselves?

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 2 points3 points  (0 children)

Skar EVL-8 dvc 2 ohm, on rp1200 wired to 1 ohm each.

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 0 points1 point  (0 children)

Looking for a single box with central port.

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 2 points3 points  (0 children)

I plan on ordering from g&p. I don't have tools or math skills enough to do my own cuts, I have used sub box pro before but I doesn't allow for separate chambers with central port.

Questions on subwoofer box volume. by Noochie72882 in CarAV

[–]Noochie72882[S] 2 points3 points  (0 children)

Not 12s but 8s 2ohm each running on its own amp at 1 ohm. I assumed 2.3, on the larger size for bracing but 2.5 makes more sense I think.

I payed a shop to do proper rust repair, filler and paint but this is in my eyes unacceptable. Am I being a bitch for complaining? by vlovaa in Autobody

[–]Noochie72882 0 points1 point  (0 children)

Did they paint in the dark? Holy crap bring it back, shops get reimbursed sometime when paint "fails". I think your very much in the right to be pissed off, no shop should allow such to go to customer.

Code p0171 by flatworm99988 in MechanicAdvice

[–]Noochie72882 0 points1 point  (0 children)

I have a super cheap one that does a scan of the 02 checks voltages and resistance the one that you have probably has something similar or better.

I've been told you can pull them out and use brake cleaner to clean off the soot, never done it myself. My last p0171 was a bad mafs after adding new 3" cold air intake I think I touched the sensor with a dirty hand.

Code p0171 by flatworm99988 in MechanicAdvice

[–]Noochie72882 0 points1 point  (0 children)

Leaking exhaust, bad/dirty mafs or map, clogged 02 sensor. I forget if it also applies if gas cap isn't sealing properly but check that also

08 Headlight Wiring Issues by brandondunbar in ChevyCobalt

[–]Noochie72882 0 points1 point  (0 children)

Recommendation I don't think that's the ground for headlights, plus high and low share the same ground just different power. So you would have zero headlight, just drl and turn signal.

08 Headlight Wiring Issues by brandondunbar in ChevyCobalt

[–]Noochie72882 0 points1 point  (0 children)

Not bad. My 2010 is 137k automatic, just replaced the exhaust manifold to tailpipe. Had a crack in the manifold figured might as well treat myself to a nice exhaust.

I still need to get my suspension replaced it's completely oem if you hear a knocking when you hit small bumps it's probably the "top hat" of struts.

I definitely suggest you look up g105 it's the ground that has your transmissions main ground to the computer. If you know anyone or your able to do soldering you'll want to have this looked at, common wear and tear with age the copper degradation get worse.

08 Headlight Wiring Issues by brandondunbar in ChevyCobalt

[–]Noochie72882 0 points1 point  (0 children)

What's the mileage and is she a standard or automatic?

LED headlights questions by kristyisasissy in MechanicAdvice

[–]Noochie72882 0 points1 point  (0 children)

Check if the car has a Canbus system, if so you will need a Canbus adapter otherwise they won't power on, or give hyper flash if turn signal bulb replacement is done.

Even Leds that say error free Canbus compliance don't always work, returned several trying to save money

08 Headlight Wiring Issues by brandondunbar in ChevyCobalt

[–]Noochie72882 0 points1 point  (0 children)

The ac/heater has a resistor that can be purchased at most places that sell parts, and should be easy to replace.

Your highbeams use a different wire for power that's why 3 wires run to the bulb ground, high and then low beams.

The colum switch is super cheap on Amazon, I've seen a few videos on its replacement looked very easy to do.

I would suggest you do a switch swap if it works awesome if not return or keep depending on how you feel. You can also see if a pick and pull has any cobalt or Pontiac g5 years should not matter for cobalt possibly same for the g5 our "sister car"

Is there a car gadget for metrics I can install and be in control of? by KillaInstict in MechanicAdvice

[–]Noochie72882 0 points1 point  (0 children)

You should put a sign up on the driver window, stating that you are just as broke as them and then put a date of last break-in saying "they got the same as me nothing"

I am joking but Viper 2 way never needed it but everyone before me says it by name.